显示标签为“DTH Drilling Rig”的博文。显示所有博文
显示标签为“DTH Drilling Rig”的博文。显示所有博文

2021年1月6日星期三

What are the operating procedures of DTH drilling rigs?

 The DTH drilling rig is common drilling equipment, mainly composed of a rotating mechanism, lifting mechanism, pushing mechanism, supporting mechanism, and impact mechanism. It has the characteristics of fast drilling speed and convenient operation. The operating rules of the down-the-hole drill are as follows:

(1) Installation and preparation of down-the-hole drill rig

1. After the cave is ready to be drilled, its specifications can be determined according to the drilling method. Generally, when drilling horizontal holes, the height of the cave is 2.6-2.8 meters, and in upward, downward, or inclined holes, the width, and height of the cave are 2.5 meters and 2.8-3 meters, respectively.

2. Gas and water pipes, lighting lines, etc. should be led near the working surface for use.

3. According to the design requirements of the hole, the bracket should be firmly fixed. The upper and lower ends of the support rods should be covered with wooden planks. The horizontal shaft and buckle are mounted on the pillar at a certain height and direction. The manual winch is used to lift the machine and fix it on the pillar according to the required angle, and then adjust the hole direction of the drilling machine.

(2) Check before the operation

1. When starting to work, please carefully check whether the air and water pipes are firmly connected and whether there is air or water leakage.

2. Check whether the oiler is full of oil.

3. Check whether the screws, nuts, connectors, etc. of each part have been tightened and whether the chromatographic column is firmly supported.

(3) Drilling procedure

When opening the hole, please start the motor first and pull the pusher of the robot after the normal transfer. Make it get proper propulsion, and then pull the handle that controls the impactor to the working position. After drilling the hole, you can open the water valve to keep the air-water mixture in an appropriate ratio. Perform regular rock drilling. When pushing the wire stripper to collide with the tool holder, a drill rod will be drilled out. It is necessary to stop the operation of the motor and supply air and water to the impactor, insert the fork into the drill pipe slot of the tool holder, reverse the motor, move the slide plate backward, and disconnect the joint pipe from the drill bit, and then connect the next drill pipe to Work continuously according to this cycle.

Related YG Machinery Products:

Choose the right water well drilling rig at YG Machinery. We have hydraulic core drilling rigs, small water well drilling rigs, crawler water well drilling rigs, trailer mounted water well drilling rigs, tractor type water well drilling rigs, small support type DTH drilling rigs, crawler DTH drilling rigs, rotary drilling rigs, horizontal directional drilling rigs, diamond core drilling rigs, spindle core drilling rigs, etc., we can meet the different needs of different customers. In addition, there are drill pipes, drill bits, air compressors, mud pumps, and other accessories. Are you looking for a drilling rig that suits you? Please contact us!【Whatsapp/Wechat/Phone/Skype】+8613613856800

2019年11月2日星期六

DTH Drilling

Product Description:

The DTH drilling rig is an impact rotary drilling rig. Its internal structure is different from that of a general rock drilling machine. Its gas distribution and reciprocating mechanism is the impactor. The front end is directly connected to the drill bit, and the rear end is connected to the drill bit, and the rear end is connected to the drill pipe. During the rock drilling, the impactor is in the hole of the submerged person, and the ( hammer ) in the impactor is struck by the gas distribution device ( valve ) to strike the shank, so that the drill bit produces a swirling force on the rock at the bottom of the hole.

Use Introduction:

It is suitable for large diameter blasthole rock drilling operations in small and medium-sized mines, road construction, water conservancy and stone works, as well as drilling anchor holes in slope support, tunnel support and foundation pit support. The main perforated object is the rock formation.

Features:

It is small in size and light in weight, and is suitable for places where large and medium-sized drilling rigs cannot work. It is convenient and flexible. The DTH drilling rig uses electric energy as power, wit low noise and strong power. The drilling speed is 3-8 times that of the general rock drill, the rock hardness is 9 and the drilling depth per hour is 8-16 meters.
The DTH drilling rig adopts an excellent motor, which has the characteristics of high efficiency, convenient operation, low investment and high economic benefit. Widely used in slope support, quarry, water conservancy projects, anchor bolts, highway and railway construction.

SKD70 DTH Drilling Rig:

The SKD70 is a hybrid powertrain with motor and compressed air. The power of the rig’s rotation is from the motor, and the impact of the impactor comes from the compressed air. When the motor is working, the electric energy is converted into the rotating torque and transmitted to the reducer, so that the drill pipe connected to the output shaft of the reducer rotates, and the alloy drill bit at the front end of the impactor continuously impacts the crushed and crushed rock, and the broken rock is taken from the vent hole of the drill bit. The discharged air pressure is blown to the ground.
The SKD70 rig is a light and economical, and it is a negligible road on the construction site and a steep star on the hillside. Mainly used in slope support, highway and railway excavation construction.
SKD70 DTH Drilling Rig

SKD100 DTH Drilling Rig:

The SKD100 rig is also a hybrid powertrainn with a motor and compressed air. SKD100 drilling rig is the main model of our company, with stable quality, convenient operation, reasonable design, slope support, quarry, water conservancy project, highway and railway construction.
SKD100 DTH Drilling Rig

SKQ100 DTH Drilling Rig:

The SKQ100 rig is a method of converting compressed air into mechanical force to break rock by using compresses air as the power. The power part is a pneumatic motor. The SKQ100 can also be constructed without electricity, with a single power, safe and reliable.
The SKQ100 drilling rig is suitable for water conservancy projects, underground mining projects, road and railway construction, etc.
The SKQ100 column drilling rig is specially designed for tunnel engineering and underground engineering. The column can be adjusted up and down, and the rig is placed on the middle tray for 360 degree rotation.
The SKQ100 long and short carriages are often used on the columns. Both rigs, the upper and lower telescopic cylinders are active throughout the carriage. The long carriage is equipped with a 1 meter drill pipe and the short carriage is equipped with a half meter drill pipe. This depends on the specific construction environment at the site to decide which rig to choose. Widely used in underground engineering, tunnel engineering.
SKQ100 DTH Drilling Rig
SKB120-5.5 DTH Drilling Rig:
The SKB120-5.5 cycloidal drill is a hybrid powertrain with a motor and compressed air. The SKB120-5.5 cycloidal drill has high torque and strong drilling capability. It is the best choice for deep hole blasting. SKB120-5.5 drilling rig is suitable for slope support, quarry, water conservancy project, highway and railway construction.
SKB120-5.5 DTH Drilling Rig